杭州消防工程设计审核办理的具体步骤

　　消防设计审核是早期匹配过程中一个复杂、困难、长期的过程。由于消防队与建设项目用地规划部门属于平行部门，有些手续可以并行办理。对早期匹配工程师的建议是尽早与消防队沟通，并在条件允许的情况下提前检查图纸。为了避免不均匀的工序和无法开始施工。

　　《中华人民共和国消防法》第十一条：大型人员密集场所和国务院公安部门规定的其他特种建设项目，建设单位应当向公安机关消防机构报送消防设计文件。供审核。

　　《中华人民共和国消防法》第十二条：依法应当经公安机关消防机构审核的建筑工程，由审批该建筑工程施工许可证的部门不得发给施工许可证，并不得施工。建筑施工单位和施工单位不得施工;已经取得施工许可证的其他建筑工程，应当依法进行抽查。未竣工的，停止施工。

　　以上两条引自《中华人民共和国消防法》。消防设计审核主要针对建筑、给排水、电气等专业。然而，在没有消防设计审核的情况下，桩基工程是不允许建造的。否则，将对施工单位和施工单位处以罚款。

　　在这里，消防设计审核是针对建筑施工项目，根据我自己的经验，可以分为空白类型、精装类型两种类型，这意味着当干燥的空白房间需要为消防设计审核申报时，当完成空白房间时，还需要申报消防设计审核以进行精细装修。(有平方米限制，低于300_或投资)。不需要处理30万人以下的人员，但如果人员拥挤的地方，不需要处理，直到200人以下)。验收过程中，未进行消防设计审核和申报工作的，不予验收。向当地消防队申报已完成土建消防设计审核和精装消防设计审核后，可进行逐级验收(先土建后精装)和土建精装的统一验收。(俗称两报一考)

　　认真地说，下面是如何进行消防设计审核的简要说明：

　　1、处理的前提条件：

　　2、取得建设工程规划许可证。

　　3、获得地图检查证书。

　　4、获得消防通知。

　　5、完成建筑、结构、管道和电气图纸和文件的设计。(装饰装修图设计)

　　6、加工要求：

　　7、《建筑工程消防设计审核申报表》(以下简称：消防队以下5000，消防队以上5000，特别是重大工程需要消防队处理)、《小型工程消防设计审核记录表》、《大型工程消防设计审核表》形式

　　很明显，注意力的程度是不同的…注：记录表是直接办理竣工图的提供，以取得记录证书，但设计审核表需要完善资料，报当地消防队报建，竣工图审核合格后，可在设计奥迪完成后出具图纸审核。T证书…

　　8、两份营业执照和组织机构代码证。(盖建设单位章)

　　9、法人身份证、授权委托书、受托人身份证。(盖建设单位章)

　　10、建筑工程规划许可证(精装修消防设计审核还需提供民用消防设计审核证书)

　　11、设计单位和图纸审查单位的组织机构代码证、营业执照，设计单位和图纸审查人员的单位资格证(分别加盖设计单位、图纸审查机构和施工单位公章)单位)各两份。

　　12、完整的专业图纸

　　13、外部热输入设计实践

Fire design audit is a complex, difficult and long-term process in the early matching process. Because the fire brigade and the land planning department of construction projects belong to parallel departments, some procedures can be handled concurrently. The suggestion for early matching engineers is to communicate with the fire brigade as soon as possible and check the drawings in advance if conditions permit. In order to avoid uneven work procedures and inability to start construction.

Article 11 of the Fire Protection Law of the People's Republic of China: For large-scale personnel-intensive places and other special construction projects stipulated by the public security department under the State Council, the construction unit shall submit fire protection design documents to the fire control institutions of public security organs. For review.

Article 12 of the Fire Protection Law of the People's Republic of China: Construction projects that should be examined and verified by fire control agencies of public security organs according to law shall not be granted construction permits or constructed by the departments that examine and approve the construction permits of such construction projects. Construction units and construction units shall not construct; other construction projects that have obtained construction permits shall be subject to spot checks according to law. If the project is not completed, the construction shall be stopped.

The above two are quoted from the Fire Protection Law of the People's Republic of China. Fire design audit is mainly aimed at building, water supply and drainage, electrical and other specialties. However, in the absence of fire design audits, pile foundation engineering is not allowed to be constructed. Otherwise, the construction unit and the construction unit will be fined.

Here, fire design audit is for building construction projects. According to my own experience, it can be divided into two types: blank type and hardcover type. This means that when dry blank room needs to be declared for fire design audit, when the blank room is completed, it also needs to declare fire design audit for fine decoration. 。 (There is a square metre limit, less than 300 or investment). There is no need to deal with people under 300,000, but if there are crowded places, there is no need to deal with them until 200 people or less. In the process of acceptance, those who fail to check and declare fire control design shall not be accepted. After declaring to the local fire brigade that the civil fire protection design audit and the hardcover fire protection design audit have been completed, the step-by-step acceptance (first civil construction and then hardcover) and the unified acceptance of the civil hardcover can be carried out. (commonly known as two newspapers and one examination)

Seriously speaking, the following is a brief description of how to conduct fire design audits:

1. Prerequisites for processing:

2. Obtain construction project planning license.

3. Obtain the map inspection certificate.

4. Get fire control notice.

5. Complete the design of building, structure, pipeline and electrical drawings and documents. (Decoration design)

6. Processing requirements:

7. Fire Design Audit Declaration Form for Construction Engineering (hereinafter referred to as: Fire Brigade below 5000, Fire Brigade above 5000, especially major projects need fire brigade processing), "Fire Design Audit Record Form for Small-scale Engineering" and "Fire Design Audit Form for Large-scale Engineering" forms

Obviously, the degree of attention varies. Note: Record sheet is to provide the completed drawings directly to obtain the record certificate, but the design audit sheet needs to improve the information and report to the local fire brigade for construction. When the completed drawings are qualified, the drawings can be issued after the completion of the design auditing by Audi. T certificate...

8. Two business licenses and organization code certificates. (Stamp of Construction Unit)

9. Legal person identity card, power of attorney and trustee identity card. (Stamp of Construction Unit)

10. Construction Engineering Planning License (Civil Fire Design Audit Certificate is also required for fire design audit of fine decoration)

11. Two copies of the organization code certificate, business license of the design unit and the drawing examination unit, and the unit qualification certificate of the design unit and the drawing examination personnel (with the official seal of the design unit, the drawing examination organization and the construction unit respectively).

12. Complete professional drawings

13. Design Practice of External Heat Input