七氟丙烷灭火设备使用中应该注意哪些事项

　　七氟丙烷因其具有无色、无味、灭火效率高，而且无污染不导电的优良性能，所以大量投入到灭火系统的使用中。所以七氟丙烷灭火系统具有设计先进、性能可靠，操作简单，环保良好等特点，在大型建筑消防灭火当中被大量采用，下面，就七氟丙烷灭火系统的使用进行介绍。

　　1、本品适用环境温度为：0℃～50℃，相对湿度≤95%(40℃±2℃)。

　　2、保护区域的空气中不得含有易爆、导电尘埃及腐蚀部件的有害物质，否则必须予以保护，系统不得受到震动和撞击。

　　3、瓶组架必须安装牢固。

　　4、操作人员须经过培训合格后方可操作，严禁其他人员触摸。

　　5、灭火系统喷射灭火剂前，所有人员必须在延时期内撤离火情现场，灭火完毕后，必须首先启动风机，将废气排出后，工作人员方可进入现场。

　　6、启动瓶、储瓶在运输过程中，应轻装轻卸，防止碰撞、卧置、倒置，启动瓶、储瓶应避免接近热源。

　　7、更换新的膜片时必须使用由我公司提供指定的供应商的产品，不得随意用未经试验的膜片代用。

　　8、在日常维护、保养或进行周期检查时应严格按照操作程序，确保防止灭火剂的误喷。

　　9、拆装过程中应避免碰伤表面而影响外观。

　　10、无关人员切勿乱摸乱动本系统的零部件，以免发生意外。

　　11、杜绝对没有经过消防培训的人员对本设备进行维护保养。

　　Sevoflurane has been widely used in fire extinguishing systems because of its colorless, odorless, high fire-extinguishing efficiency, non-pollution and non-conductive properties. Therefore, sevoflurane fire extinguishing system has the characteristics of advanced design, reliable performance, simple operation, good environmental protection, etc., which is widely used in the fire extinguishing of large buildings. The following is an introduction to the use of sevoflurane fire extinguishing system.

　　1. The applicable environmental temperature of this product is: 0℃ ~ 50℃, relative humidity ≤95%(40℃±2℃).

　　2. The air in the protected area shall not contain explosive, conductive dust and harmful substances of corroded parts; otherwise, it shall be protected and the system shall not be shaken or hit.

　　3. The bottle rack must be installed firmly.

　　4. Operators shall be trained and qualified before operation. It is strictly prohibited for other personnel to touch.

　　5. Before the fire extinguishing system spraying the fire extinguishing agent, all personnel must leave the fire site within the delay period. After the fire extinguishing is completed, the fan must be started and the exhaust gas discharged before the staff can enter the site.

　　6. In the process of transportation, the starter and storage bottles should be loaded and unloaded lightly to avoid collision, horizontal position and inversion. The starter and storage bottles should avoid approaching heat source.

　　7. When replacing the new diaphragm, the product of the supplier designated by our company shall be used, and the untested diaphragm shall not be used at will.

　　8, in the daily maintenance, maintenance or periodic inspection should be in strict accordance with the operating procedures, to ensure that to prevent the accidental spray of extinguishing agent.

　　9. In the process of disassembly and assembly, avoid touching the surface and affecting the appearance.

　　10. Irrelevant personnel should not touch the parts of the system in order to avoid accidents.

　　11. It is prohibited to maintain the equipment for personnel who have not received fire protection training.